Polaris Home
Polaris Home
Find a Retailer

Polaris Quattro® P40

Maximum Pressure. Maximum Clean.

SKU #F40

Get $150 rebate!Details

Designed to devour debris, the Polaris Quattro® P40 boasts 4WD agility to aggressively climb walls and brush the waterline. Even acorns, leaves and pebbles don’t stand a chance thanks to its extra-large intake. And with dual-stage filtration, this cutting-edge pressure-side cleaner collects both fine and large debris into an easy-clean canister with a transparent window. Powered by a booster pump, the Quattro P40 is ideal for all in-ground pool surfaces.

Buy at Leslie's Pool

View Specifications

Polaris Quattro® P40 Features

Polaris Quattro® P40 Specifications

Polaris Quattro® P40 User Guides

Document ID 4411_SL
Description Polaris P40 Brochure
File Size 7.98 MB
|
File Type PDF

Polaris Quattro® P40 Frequently asked questions

  1. Verify that the feed hose is within 6" (further or shorter) than the farthest point of the pool.
  2. Check the brass insert on the single side wheel. If it has come loose, replace it.
  3. Verify the thrust jet is in the correct position.
  4. Check to see if drive chain has disengaged.
  5. Ensure the backup valve is cycling.
  1. Make sure that the blue reducing disk has not been installed in the quick disconnect.
  2. Check that the metal pre-filter is present and not clogged.
  3. Make sure that the hose weight adjustment nut is screwed down correctly.
  4. Make sure the hoses have been cut as indicated in the instructions.
  5. Check that the booster pump is working normally.
  6. Check that the wheels are turning between 28 and 34 times per minute.
  7. Check that the pivoting connectors are fitted the right way round.
  8. Check the orientation of the rear drive jet.
  9. Replace standard tires with tires for tiled or glass surfaces (Ref. C-136).
  1. Check the wheel RPM's.
  2. Verify the backup valve is cycling. Lift the valve out of the water and watch the jet. It should come on and turn off.
  3. Adjust the thrust jet.
  4. Remove unnecessary pool hardware or install a ladder guard (part # G21)
  1. Check for air in the filter bag. (presence of air indicates a suction side air leak. It's also common for the system to purge air if solar is being used.
  2. Ensure the backup valve isn't running constantly.
  3. Ensure proper placement of the hose floats. Ensure there is no hose float between the backup valve and cleaner head.
  1. Check wheel RPM and pressure to verify proper flow.
  2. Check to see if drive chain has disengaged.
  3. Check inline filter screen for blockage.
  4. Check the water management system for obstructions.
  1. Ensure cleaner is running with proper flow.
  2. Check the water management jets for obstructions. Use a paper clip to remove debris from jets if necessary.
  3. Ensure filter bag is empty.
  1. Check the filter bag. If it's full it can weigh the cleaner down on one side. Empty or replace the bag.
  2. Verify the thrust jet is at the 7 O'clock position.
  3. Check the brass insert on the single side wheel. If it has come loose, replace and check the wheel for proper operation.
  4. Check feed hose to ensure the floats are spaced evenly.
  5. Check for water inside the head float.
  6. Check the wheel RPM. If more than 36, make an adjustment to reduce the flow.
  1. Check the filter screen in the inline filter assembly on the hose and clean if necessary.
  2. Ensure the skimmer basket, pump basket and pool filter are clean.
  3. Check hoses, hose connections, backup valve and swivels for leaks that could cause loss of water pressure.
  4. Check the wheel RPM. If below 30 RPM, see the wheel RPM adjustment process in the manual to increase flow to the cleaner.
  5. Ensure drive chain is engaged.
  6. Ensure bearings are clear from debris. Replace if worn.
  7. Change or remove restrictor disk if necessary.
  1. Check the wheel RPM. If more than 36, make an adjustment to reduce the flow.
  2. Verify the backup valve is cycling.
  1. Turn the appliance over and check the suction by making sure that all the jets located in the central pipework are working correctly. If they aren’t, make sure they are not blocked.
  2. Fit the special tires for smooth tiled surfaces (Ref. C-13).
  1. Check the wheel RPM. If not in the 30-36 RPM range, refer to the manual for adjusting the wheel RPM.
  2. Adjust the thrust jet downward.
  3. Verify the backup valve is cycling. Lift the valve out of the water and watch the jet. It should come on and go off.
  4. Check for water inside the head float.
  5. Empty the filter bag.
  1. Ensure the opening at the end of the sweep hose is not blocked by the sweep hose scrubber. Replace the scrubber if worn or missing.
  2. Check the wheel RPM. If more than 36, make an adjustment to reduce the flow.
  3. Add a sweep hose weight. (part number B2)
  1. Adjust the flow to the speed hose using the easy click settings or the adjustment screw.
  2. Replace the scrubber if it is worn or missing.
  3. Pull the sweep hose scrubber down to cover more of the tip of the hose.
  4. Add a sweep hose weight. (part number B2)
Check swivels and make sure they are spinning freely. Lay the hose out in the sun for 24 hours to eliminate any potential hose memory.
  1. Use the Polaris pressure tester to check the booster pump pressure.
  2. Check that the metal pre-filter is present and not clogged.
  3. Make sure that the hose weight adjustment nut is screwed down correctly.
  4. Make sure the hoses have been cut as indicated in the instructions.
  5. Make sure that the blue reducing disk has not been installed in the quick disconnect.
  6. Check that the booster pump is working normally.
  7. Clean the skimmer baskets, sand filter, and pump basket.
  1. Unscrew the hose-weight adjustment nut until the desired setting is obtained.
  2. Fit the flow limiter (red or blue) into the quick disconnect.
Verify the wheel RPM's are in range. If they are low or the wheels are not spinning then check the in-line filter for debris. If clear and the wheels still aren't spinning then check the water management system for clogs. If the RPM's are slightly below the prescribed range then remove the restrictor disc from the wall connector. If the wheels are moving too quickly then install the red restrictor disc.
Verify that the wheel RPM's are in the correct range and adjust the thrust jet. If the cleaner isn't climbing well then ensure the thrust jet is in the 11 o'clock position. If it is going in circles then angle the thrust jet so it is pointing opposite of the way the cleaner is turning. For example, if the cleaner is turning right then point the thrust jet to the left.
Verify the wheel RPM's are in range. Ensure that the head float is not filled with water. Try running the cleaner without the bag and if it fixes the issue then clean the bag with soap and warm water. This will remove any biofilm/oils that may have accumulated in the bag.

Polaris Quattro® P40 Related Products

Polaris Quattro Sport Pressure Pool Cleaner

Polaris Quattro® Sport

4.7 Stars (246 Reviews)

Designed to devour debris, the Polaris Quattro® Sport aggressively climbs walls and brushes the waterline.

View details
PB4SQ Booster

Polaris PB4SQ

4.9 Stars (77 Reviews)

The PB4SQ is an energy-efficient, multistage booster pump
that operates quietly and is easy to install and service.

View details
Polaris PB4-60 Booster Pool Pumps

Polaris PB4-60

4.9 Stars (1000 Reviews)

The PB4-60 delivers the best combination of high-performance power, quiet operation, and durability.

View details

Polaris Quattro® P40 Spare Parts & Accessories

R0995100
R0995100

R0995100 Polaris Quattro™ Factory Tune-Up Kit

This tune-up kit is a convenient repair kit equipped with key parts to rejuvenate and extend the life of any QUATTRO cleaner.